Technical Vocabulary

Technical Vocabulary

Accessible - (As applied to wiring methods) Capable of being removed or exposed without damaging the building structure or finish, or not permanently closed in by the structure or finish of the building.

Accessible - (as applied to equipment) Admitting close approach: not guarded by locked doors, elevation, or other effective means. (see Accessible, Readily)

Accessible, Readily - (Readily Accessible) Capable of being reached quickly for operation, renewal, or inspections, without requiring those to whom ready access is requisite to climb over or remove obstacles or to resort to portable ladders,chairs,etc.

Ambient Temperature - The temperature of the air, water, or surrounding earth. Conductor ampacity is corrected for changes in ambient temperature including temperatures below 86°F. The cooling effect can increase the current carrying capacity of the conductor. (Review Section 310-10 of the Electrical Code for more understanding)

Ammeter - An electric meter used to measure current, calibrated in amperes.

Ampacity - The current-carrying capacity of conductors or equipment, expressed in amperes.

Ampere - The basic SI unit measuring the quantity of electricity.

Bonding Jumper - A bare or insulated conductor used to ensure the required electrical conductivity between metal parts required to be electrically connected. Frequently used from a bonding bushing to the service equipment enclosure to provide a path around concentric knockouts in an enclosure wall: also used to bond one raceway to another.

Continuity - The state of being whole, unbroken.

Continuos Load - A load where the maximum current is expected to continue for three hours or more. Rating of the branch circuit protection device shall not be less tan 125% of the continuos load.

Demand Factor - For an electrical system or feeder circuit, this is a ratio of the amount of connected load (in kva or amperes) that will be operating at the same time to the total amount of connected load on the circuit. An 80% demand factor, for instance, indicates that only 80% of the connected load on a circuit will ever be operating at the same time. Conductor capacity can be based on that amount of load.

Dustproof - Constructed or protected so that dust will not interfere with its successful operation.

Dusttight - Constructed so that dust will not enter the enclosing case under specified test conditions.

Duty, continuos - A service requirement that demands operation at a substantially constant load for an indefinitely long time.

Duty, intermittent - A service requirement that demands operation for alternate intervals of load and no load, load and rest, or load, no load, and rest.

Duty, periodic - A type of intermittent duty in which the load conditions regularly reoccur.

Duty, short time - A requirement of service that demands operations at a substantially constant load for a short and definitely specified time.

Duty, varying - A requirement of of service that demands operation at loads, and for intervals of time, both of which may be subject to wide variation.

Explosionproof - Designed and constructed to withstand and internal explosion without creating an external explosion or fire.

Feeder - A circuit, such as conductors in conduit or a busway run, which carries a large block of power from the service equipment to a sub-feeder panel or a branch circuit panel or to some point at which the block power is broken into smaller circuits.

Ground - A large conducting body (as the earth) used as a common return for an electric circuit and as an arbitrary zero of potential.

Grounded, effectively - Intentionally connected to earth through a ground connection or connections of sufficiently low impedance and

having sufficient current-carrying capacity to prevent the buildup of voltages that may result in undue hazards to connect equipment or to persons.

Grounded Conductor - A system or circuit conductor that is intentionally grounded, usually gray or white in color.

Grounding Conductor - A conductor used to connect metal equipment enclosures and/or the system grounded conductor to a grounding electrode, such as the ground wire run to the water pipe at a service; also may be a bare or insulated conductor used to ground motor frames, panel boxes, and other metal equipment enclosures used throughout electrical systems. In most conduit systems, the conduit is used as the ground conductor.

Grounding Equipment Conductor - The conductor used to connect the noncurrent-carrying metal parts of equipment, raceways, and other enclosures to the system grounded conductor, the grounding electrode conductor, or both, of the circuit at the service equipment or at the source of a separately derived system.

Grounding Electrode - The conductor used to connect the grounding electrode to the equipment grounding conductor, to the grounded conductor, or to both, of the circuit at the service equipment or at the source of a separately derived system.

Ground Fault Circuit Interrupter - A device intended for the protection of personal that functions to de-energize a circuit or portion thereof within an established period of time when a current to ground exceeds some predetermined value that is less than required to operate the overcurrent protection device of the supply circuit.

Ground Fault Protection of Equipment - A system intended to provide protection of equipment from damaging line to ground fault currents by operating to cause a disconnecting means to open all ungrounded conductors of the faulted circuit. This protection is provided at current levels less than those required to protect conductors from damage through the operations of a supply circuit overcurrent device.

In Sight From - (within sight from, within sight) Where this Code specifies that one equipment shall be "in sight from", "within sight from" or m"within sight", etc. of another equipment, the specified equipment is to be visible and not more that 50´ distant from the other

Interrupter Rating - The highest current at rated voltage that a device is intended to interrupt under standard test conditions.

Labeled - Items to which a label, trademark, or other identifying mark of nationally recognized testing labs has been attached to indentify the items as having been tested and meeting appropriate standards.

Listed - Equipment or materials included in a list published by an organization acceptable to the authority having jurisdiction and concerned with product evaluation, that maintains periodic inspection of production of listed equipment or materials, and whose listing states either that the equipment or material meets appropriate designated standards or has been tested and found suitable for use in specified manner.

Location, damp - A location subject to moderate amount of moisture such as some basements, barns, cold storage, warehouse and the like.

Location, dry - A location not normally subject to dampness or wetness: a location classified as dry may be temporarily subject to dampness or wetness, as in case of a building under construction.

Location, wet - A location subject to saturation with water or other liquids.

Megger - A test instrument for measuring the insulation resistance of conductors and other electrical equipment; specifically, a mega ohm (million ohms) meter; this is a registered trade mark of the James Biddle Co.

Mega ohm - A unit of electrical resistance equal to one million ohms.

Mega ohmmeter - An instrument for measuring extremely high resistance.

No inductive Circuit - A circuit in which the magnetic effect of the current flowing has been reduced by one several methods to a minimum or to zero.

Nonlinear Load - A load where the wave shape of the steady state current does not follow the wave shape of the applied voltage.

Ohm - The derived SI unit for electrical resistance or impedance; one ohm equals one volt per am-pere.

Ohmmeter - an instrument for measuring resistance in ohms. Take a look at this diagram to see how an ohmeter is used to check a small control transformer. The ohmmeter's pointer deflection is controlled by the amount of battery current passing through the moving coil. Before measuring the resistance of an unknown resistor or electrical circuit, the ohmmeter must first be calibrated. If the value of resistance to be measured can be estimated within reasonable limits, a range selected that will give approximately half-scale deflection when the resistance is inserted between the probes. If the resistance is unknown, the selector switch is set on the highest scale. Whatever range is selected, the meter must be calibrated to read zero before the unknown resistance is measured.

Over current - Any current in excess of the rated current of equipment or the capacity of a conductor. It may result from overload, short circuit or ground fault.

Overload - Load greater than the load for which the system or mechanism was intended. A fault, such as a short circuit or ground fault, is not an overload.

Panel board - A single panel or group of panel units designed for assembly in the form of a single panel: includes buses and may come with or without switches and/or automatic over current protective devices for the control of light, heat, or power circuits of individual as well as aggregate capacity. It is designed to be placed in a cabinet or cutout box that is in or against a wall or partition and is accessible only from the front.

Plenum - Chamber or space forming a part of an air conditioning system

Rainproof - So constructed, projected, or treated as to prevent rain from interfering with the successful operation of the apparatus under specified test conditions.

Rain tight - So constructed or protected that exposure to a beating rain will not result in the entrance of water.

Separately Derived System - A premises wiring system whose power is derived from a battery, a solar photovoltaic system, or from a generator, transformer, or converter windings, and that has no direct electrical connection, including solidly connected grounded circuit conductor, to supply conductors originating in another system.

Service Drop - Run of cables from the power company's aerial power lines to the point of connection to a customer's premises.

Service Conductors - The supply conductors that extend from the street main or transformers to the service equipment of the premises being supplied

Service Entrance Conductors - (Overhead) The service conductors between the terminals of the service equipment and a point usually outside the building, clear of building walls, where joined by tap or splice to the service drop.

Service Entrance Conductors - (Underground) The service conductors between the terminals of the service equipment and the point of connection to the service lateral.

Service Equipment - The necessary equipment, usually consisting of a circuit breaker or switch and fuses and their accessories, located near the point entrance of supply conductors to a building and intended to constitute the main control and cutoff means for the supply to the building. Service Lateral- The underground service conductors between the street main, including any risers at a pole or other structure or from transformers, and the first point of connection to the service-entrance conductors in a terminal box, meter, or other enclosure with adequate space, inside or outside the building wall. Where there is no terminal box, meter, or other enclosure with adequate space, the point of connection is the entrance point of the service conductors into the building.

Service Point - The point of connection between the facilities of the serving utility and the premises wiring.

Switchboard - A large single panel, frame, or assembly of panels having switches, over current, and other protective devices, buses, and usually instruments mounted on the face or back or both. Switchboards are generally accessible from the rear and from the front and are not intended to be installed in cabinets.

Switch, general use - A switch intended for use in general distribution and branch circuits. It is rated in amperes and is capable of interrupting its rated voltage.

Switch, general-use snap - A type of general-use switch so constructed that it can be installed in flush device boxes or on outlet covers, or otherwise used in conjunction with wiring systems recognized by the National Electric Code.

Switch, isolating - A switch intended for isolating an electrical circuit from the source of power. It has no interrupting rating and is intended to be operated only after the circuit has been opened by some other means.

Switch, knife - A switch in which the circuit is closed by a moving blade engaging contact clips.

Switch, motor-circuit - A switch, rated in horsepower, capable of interrupting the maximum operating overload current of a motor of the same horsepower rating as the switch at the rated voltage.

Switch, transfer - A transfer switch is an automatic or nonautomatic device for transferring one or more load conductor connections from one power source to another.

Switch-Leg - That part of a circuit run from a lighting outlet box where a luminaries or lamp holder is installed down to an outlet box that contains the wall switch that turns the light or other load on or off: it is a control leg of the branch circuit. Voltage Drop - The loss of voltage between the input to a device and the output from a device due to the internal impedance or resistance of the device. In all electrical systems, the conductors should be sized so that the voltage drop never exceeds 3% for power, heating, and lighting loads or combinations of these. Furthermore, the maximum total voltage drop for conductors for feeders and branch circuits combined should never exceed 5%.

Watertight - So constructed that water/moisture will not enter the enclosure under specified test conditions.

Weatherproof - So constructed or protected that exposure to the weather will not interfere with successful operation.